Study on Microstructrue and Mechanical Properties of Electron Beam Welded AF1410 Joints

TANG Daibin; LI Kai; MAO Zhiyong; WU Bing

您当前的位置：

首页 >

文章列表页 >

Study on Microstructrue and Mechanical Properties of Electron Beam Welded AF1410 Joints

更新时间：2025-10-30

- Study on Microstructrue and Mechanical Properties of Electron Beam Welded AF1410 Joints
- Aeronautical Manufacturing Technology Vol. 60, Issue 18, Pages: 93-96(2017)
- 作者机构：
  
  中国航空制造技术研究院高能束流加工技术国防科技重点实验室,北京,100024
- 作者简介：
- 基金信息：
- DOI：
  CLC：
- Published：2017
- 稿件说明：
移动端阅览
唐代斌，李　凯，毛智勇，吴　冰. AF1410 钢电子束焊接接头组织及性能研究[J]. 航空制造技术, 2017, 60(18): 93-96.

TANG Daibin, LI Kai,MAO Zhiyong, WU Bing. Study on Microstructrue and Mechanical Properties of Electron Beam Welded AF1410 Joints. Aeronautical Manufacturing Technology, 2017, 60(18): 93-96.
唐代斌，李　凯，毛智勇，吴　冰. AF1410 钢电子束焊接接头组织及性能研究[J]. 航空制造技术, 2017, 60(18): 93-96. DOI：

TANG Daibin, LI Kai,MAO Zhiyong, WU Bing. Study on Microstructrue and Mechanical Properties of Electron Beam Welded AF1410 Joints. Aeronautical Manufacturing Technology, 2017, 60(18): 93-96. DOI：

摘要

采用电子束扫描焊和修饰焊工艺对5mm AF1410 钢板进行电子束焊接。针对热处理前、后的接头，采用光学显微镜、扫描电镜、硬度仪等对其组织、硬度及拉伸断口进行分析。结果表明：接头热影响区分为浅腐蚀区和深腐蚀区，分别为单一马氏体(M)、M+ 少量逆转奥氏体(Ar) 组织；焊缝区柱状晶分为重熔区、正火区和回火区，晶内为马氏体，晶界附近为残留奥氏体。热处理后，接头组织、显微硬度与母材趋于一致，抗拉强度也达到了母材98% 以上，失效裂纹始于热影响区，呈约60°方向扩展并贯穿整个接头。

Abstract

Oscillated electron beam welding with cosmetic welding was applied to 5mm AF1410 steel. Microstructural features and tensile failure fractures of joints were examined by means of OM

SEM and microhardness tester. Results showed that the heat affected zone (HAZ) contains light etched zone and dark etched zone

which are composed of martensite (M)

M+ reverted austenite (Ar) respectively; the weld zone (WZ) is divided into 3 different zones

namely remelted zone

normalized zone and tempered zone

and occupied by columnar grains

besides martensite exists in intragranular areas and retained austenite (A) exists at intergranular areas. After post-weld heat treatment

microhardness and microstructure of joint are nearly the same as base metal. The room tensile strength of joint reaches 98% of base metal and all cracks initiate at HAZ and propagate through the whole WZ in60° direction.

关键词

Keywords

references

Views

516

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Research of Microstructure and Mechanical Properties of Electron Beam Welding Joints for TB18 Titanium Alloy

Effect of High-Energy Ultrasound on Microstructure and Mechanical Properties of Large-Scale 2219 Aluminum Alloy Ingots

Effect of Brazing Temperature on Microstructure and Mechanical Properties of GH3030/B–Ni73CrSiB–40Ni–S/GH4648 Joints

Microstructure and Properties of TiC-Reinforced 7034 Aluminum Alloy Fabricated by Wire-Feed Laser Cladding

Mechanical Properties and Deformation Behavior of TPMS Multi-Oriented Structure Fabricated by Additive Manufacturing

Related Author

GENG Kang

XU Ming

LIU Xin

FU Pengfei

LI Lihang

TANG Zhenyun

LI Anqing

JIANG Ripeng

Related Institution

Science and Technology on Power Beam Processes Laboratory, AVIC Manufacturing Technology Institute

College of Mechanical and Electrical Engineering, Central South University

State Key Laboratory of High Performance Complex Manufacturing for Extreme Service, Central South University

Institute of Light Alloys, Central South University

Xinjiang JoinWorld Co., Ltd.

The platform construction and operation are provided by Beijing Founder electronics co., LTD 京ICP备09064830号-19 京公网安备11010802024621
It is recommended to read the content of this site in Chrome&IE9+. Please switch to extreme mode in browser 360.
Cookies We use cookies to help provide and enhance our service and tailor content. By continuing, you agree to the use of cookies.
Total Visits：34721 Visits Today：199

⁰