Analysis and Calculation on Machining Deformation of Parameterized Thin-Wall Workpiece Based on ANSYS

李光; 陈五一; 张平

doi:10.16080/j.issn1671-833x.2011.19.016

您当前的位置：

首页 >

文章列表页 >

Analysis and Calculation on Machining Deformation of Parameterized Thin-Wall Workpiece Based on ANSYS

更新时间：2026-04-23

- Analysis and Calculation on Machining Deformation of Parameterized Thin-Wall Workpiece Based on ANSYS
- Aeronautical Manufacturing Technology Vol. 54, Issue 19, Pages: 76-79(2011)
- 作者机构：
  
  1. 北京航空航天大学
  2. 中航工业沈阳黎明航空发动机（集团）有限责任公司
- 作者简介：
- 基金信息：
- DOI：10.16080/j.issn1671-833x.2011.19.016
  CLC：
- Published：2011
- 稿件说明：
移动端阅览
李光，陈五一，张平. 基于 ANSYS 的参数化薄壁件加工变形分析与计算[J]. 航空制造技术, 2011, 54(19): 76-79.

李光, 陈五一, 张平. Analysis and Calculation on Machining Deformation of Parameterized Thin-Wall Workpiece Based on ANSYS[J]. Aeronautical Manufacturing Technology, 2011, 54(19): 76-79.
李光，陈五一，张平. 基于 ANSYS 的参数化薄壁件加工变形分析与计算[J]. 航空制造技术, 2011, 54(19): 76-79. DOI： 10.16080/j.issn1671-833x.2011.19.016.

李光, 陈五一, 张平. Analysis and Calculation on Machining Deformation of Parameterized Thin-Wall Workpiece Based on ANSYS[J]. Aeronautical Manufacturing Technology, 2011, 54(19): 76-79. DOI： 10.16080/j.issn1671-833x.2011.19.016.

摘要

随着对航空产品性能要求的进一步提高，现代航空工业中广泛使用薄壁件零件。由于薄壁件零件刚度差，在加工过程中极易发生变形。建立了参数化薄壁件加工过程有限元模型，借助有限元软件 ANSYS10.0 对薄壁件加工变形量进行分析计算研究。由于 ANSYS 本身功能有限，不能提供较为友好的图形化界面输入，所以基于 C# 环境完成了 ANSYS 的二次开发软件的研究，建立了友好的操作界面，用户可以直接在操作界面上输入参数，软件即可在后台调用ANSYS 进行计算，从而极大地提高了分析效率。

Abstract

With higher demanding to reduce the weight of aviation products

many components used in the aviation industry usually adopt thin-wall structures. But

because of its poor stiffness

thin-wall workpiece deforms easily in machining process. So fi nite element model of parameterized thin-wall workpiece in machining process is estabilished and the machining deformation of thin-wall workpiece is calculated by using FEM software ANSYS 10.0. Because ANSYS can’t provide a relatively friendly graphical interface

a secondary development of ANSYS is made based on C#

and a friendly interface is developed. The software developed could call ANSYS to calculate in background after the users enter the parameters

so the efficiency of analysis could increase in a large degree.

关键词

Keywords

references

Views

358

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Experiment and Numerical Simulation on Performance of TC4 Fastener

Characteristics of Reaction Force in Blasting Erosion Arc Machining of SiC/Al Composites

Application of ANSYS Structure Optimization Technology in Mechanical Design

Related Author

张杰

陶华

陈磊

刘风雷

张广来

CHEN Jipeng

HE Guojian

LIU Xiao

Related Institution

西北工业大学中法联合虚拟设计与制造研究室

北京航空制造工程研究所

中航工业沈阳飞机设计研究所

State Key Laboratory of Mechanical System and Vibration, Shanghai Jiao Tong University

Shanghai Aerospace Equipment Manufacturing

The platform construction and operation are provided by Beijing Founder electronics co., LTD 京ICP备09064830号-19 京公网安备11010802024621
It is recommended to read the content of this site in Chrome&IE9+. Please switch to extreme mode in browser 360.
Cookies We use cookies to help provide and enhance our service and tailor content. By continuing, you agree to the use of cookies.
Total Visits：24190 Visits Today：2

⁰