Characteristics of Reaction Force in Blasting Erosion Arc Machining of SiC/Al Composites

CHEN Jipeng; HE Guojian; LIU Xiao; GU Lin; ZHAO Wansheng

doi:10.16080/j.issn1671-833x.2018.03.054

您当前的位置：

首页 >

文章列表页 >

Characteristics of Reaction Force in Blasting Erosion Arc Machining of SiC/Al Composites

更新时间：2025-10-30

- Characteristics of Reaction Force in Blasting Erosion Arc Machining of SiC/Al Composites
- Aeronautical Manufacturing Technology Vol. 61, Issue 3, Pages: 54-59(2018)
- 作者机构：
  
  1. 上海交通大学机械系统与振动国家重点实验室,上海,200240
  2. 上海航天设备制造总厂,上海,200245
- 作者简介：
- 基金信息：
- DOI：10.16080/j.issn1671-833x.2018.03.054
  CLC：
- Published：2018
- 稿件说明：
移动端阅览
陈吉朋，何国健，刘晓，顾琳，赵万生. 高速电弧放电加工SiC/Al的放电作用力特性研究[J]. 航空制造技术, 2018, 61(3): 54-59.

CHEN Jipeng1, HE Guojian1, LIU Xiao2, GU Lin1, ZHAO Wansheng1. Characteristics of Reaction Force in Blasting Erosion Arc Machining of SiC/Al Composites[J]. Aeronautical Manufacturing Technology, 2018, 61(3): 54-59.
陈吉朋，何国健，刘晓，顾琳，赵万生. 高速电弧放电加工SiC/Al的放电作用力特性研究[J]. 航空制造技术, 2018, 61(3): 54-59. DOI： 10.16080/j.issn1671-833x.2018.03.054.

CHEN Jipeng1, HE Guojian1, LIU Xiao2, GU Lin1, ZHAO Wansheng1. Characteristics of Reaction Force in Blasting Erosion Arc Machining of SiC/Al Composites[J]. Aeronautical Manufacturing Technology, 2018, 61(3): 54-59. DOI： 10.16080/j.issn1671-833x.2018.03.054.

摘要

基于压电传感器，测量和研究了高速电弧放电加工SiC/Al的作用力。分析了作用力的波形特征，对比了不同放电介质中的作用力。研究了作用力的频率特性、以及作用力受脉冲宽度、峰值电流和放电电压的影响趋势，揭示了作用力与电弧放电加工时材料抛出过程的关系，给出了高速电弧放电加工航空航天SiC/Al 薄壁零件时，降低作用力的可行措施。

Abstract

This paper measured and studied the reaction force of blasting erosion arc machining (BEAM) of SiC/Al based on a piezoelectric sensor. The characteristics of the reaction force waveform was discussed

and the forces in different dielectric are compared. Then

the frequency characteristics and the relationship between reaction force and discharge parameters (pulse on time

current and open voltage) were researched. Furthermore

the influence of relationship between reaction force and the material removal mechanism of discharge processing was discussed. And finally

a method to reduce the reaction force during BEAM of thin-wall SiC/Al workpiece which is commonly used in aerospace industry was given.

关键词

Keywords

references

Views

468

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Analysis and Calculation on Machining Deformation of Parameterized Thin-Wall Workpiece Based on ANSYS

Design and Experimental Verification of Stitching Forming System for Rigid Sandwich Composite Preforms

Electromechanical Behavior of Open-Hole Three-Dimensional Angle-Interlock Woven Carbon Fiber Reinforced Polymer Under Tensile Loading

Dynamic Measurement Method for Shaft Deflection Angles in Helicopter Drive Systems

Research Progress on Matrix Composition Regulation of SiC/SiC Composites

Related Author

李光

陈五一

张平

Related Institution

北京航空航天大学

中航工业沈阳黎明航空发动机（集团）有限责任公司

The platform construction and operation are provided by Beijing Founder electronics co., LTD 京ICP备09064830号-19 京公网安备11010802024621
It is recommended to read the content of this site in Chrome&IE9+. Please switch to extreme mode in browser 360.
Cookies We use cookies to help provide and enhance our service and tailor content. By continuing, you agree to the use of cookies.
Total Visits：34573 Visits Today：51

⁰