Research on Remanufacturing and Repairing Method of Aero-Engine Blade Based on Reverse Engineering

CHEN Zhenlin; CHEN Zhitong; ZHU Zhengqing; ZHANG Yun

doi:10.16080/j.issn1671-833x.2020.23/24.080

您当前的位置：

首页 >

文章列表页 >

Research on Remanufacturing and Repairing Method of Aero-Engine Blade Based on Reverse Engineering

更新时间：2025-10-30

- Research on Remanufacturing and Repairing Method of Aero-Engine Blade Based on Reverse Engineering
- Aeronautical Manufacturing Technology Vol. 63, Issue 23/24, (2020)
- 作者机构：
  
  1. 中国航发沈阳黎明航空发动机有限责任公司,沈阳,110043
  2. 北京航空航天大学机械工程及自动化学院,北京,100191
  3. 北京航空航天大学能源与动力工程学院,北京,100191
- 作者简介：
- 基金信息：
- DOI：10.16080/j.issn1671-833x.2020.23/24.080
  CLC：
- Published：2020
- 稿件说明：
移动端阅览
陈振林，陈志同，朱正清，张云. 基于逆向工程的航空发动机叶片再制造修复方法研究[J]. 航空制造技术, 2020, 63(23/24): 80-93. CHEN Zhenlin,CHEN Zhitong,ZHU Zhengqing, ZHANG Yun. Research on Remanufacturing and Repairing Method of Aero-Engine Blade Based on Reverse Engineering. Aeronautical Manufacturing Technology, 2020, 63(23/24): 80-93.

CHEN Zhenlin, CHEN Zhitong, ZHU Zhengqing, et al. Research on Remanufacturing and Repairing Method of Aero-Engine Blade Based on Reverse Engineering[J]. Aeronautical Manufacturing Technology, 2020, 63(23/24).
陈振林，陈志同，朱正清，张云. 基于逆向工程的航空发动机叶片再制造修复方法研究[J]. 航空制造技术, 2020, 63(23/24): 80-93. CHEN Zhenlin,CHEN Zhitong,ZHU Zhengqing, ZHANG Yun. Research on Remanufacturing and Repairing Method of Aero-Engine Blade Based on Reverse Engineering. Aeronautical Manufacturing Technology, 2020, 63(23/24): 80-93. DOI： 10.16080/j.issn1671-833x.2020.23/24.080.

CHEN Zhenlin, CHEN Zhitong, ZHU Zhengqing, et al. Research on Remanufacturing and Repairing Method of Aero-Engine Blade Based on Reverse Engineering[J]. Aeronautical Manufacturing Technology, 2020, 63(23/24). DOI： 10.16080/j.issn1671-833x.2020.23/24.080.

摘要

航空发动机叶片长期服役在高温、高压和高速的环境下，极易出现损伤，而损伤叶片的修复技术一直是国内航空领域的研究重点和难点。以双联高导涡轮叶片为例，研究了一种基于逆向工程的航空发动机叶片再制造修复方法。该方法不依赖原始设计模型，而是基于同期服役非损伤叶片，这样重构的目标修复曲面更接近损伤叶片的变形状态。首先，用 3D 蓝光扫描仪扫描已损伤叶片及同期服役非损伤叶片以获取其点云模型；其次，对两叶片点云模型进行最佳拟合配准并分析识别出修复加工区域和边界；然后，基于非损伤区域配准后的误差情况，用多项式方程拟合曲线预测损伤区域的误差数据，再以非损伤叶片截面曲线为基础，叠加预测误差值求取修复区域的目标截面线；最后，通过蒙皮方法构建出目标修复曲面，编制数控加工程序，完成修复加工。以非损伤叶片的逆向模型为参考，对损伤叶片修复结果进行精度检测和误差分析。结果表明：该叶片修复轮廓精度基本上在 0.03mm 以内，满足修复公差要求，且修复区域与非修复区域能实现光滑搭接过渡，利用提出的方法对双联高导涡轮叶片有很好的修复效果。

Abstract

Aero-engine turbine blades are vulnerable to be damaged due to the serving environment of high temperature

high pressure and high speed. At present

the repair technologies of damaged blades have been a hotspot in the aircraft maintenance. In this paper

a method of remanufacturing and repairing aero-engine blades based on reverse engineering is studied by taking a turbine blade as an example. The target repairing surface reconstructed in this method based on non-damaged blade serving at the same time instead of the original design model will more accord with deformation state of damaged blades. Firstly

the damaged blade and non-damaged blade serving at the same time are scanned by the 3D blue-light scanner and the point cloud model of two blades can be acquired. Secondly

the repairing area and boundary can be identified after best fitting. And then

the errors between these two blades in repaired area will be predicted according to polynomial curves fitted by these errors in non-repaired area after registration. Furtherly

the section curves of target repairing surface can be obtained based on the predicted errors and section curves of non-damaged blade. Finally

the target repairing surface can be constructed using the skin method. And the constructed surface is used for the generation of NC tool paths which will achieve repair processing. The repaired results of the damaged blade are analyzed according to the reverse model of non-damaged blade. And the results show that the profile errors are basically within 0.03mm which meet the tolerance requirements of repairing blades and there are smooth transition between repaired and non-repaired areas. The method presented in this paper has a good effect on repairing aero-engine blades.

关键词

Keywords

references

Views

436

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Research on Properties Regulation of Thin-Walled ZL114A Parts Repaired by Magnetic Field-Assisted Wire Arc Additive

Solid-State Cold Spray Additive Manufacturing: Evolution, Current Status, and Opportunities & Challenges

Eddy Current Testing and Damage Analysis of Single Crystal Turbine Blade With Thermal Barrier Coatings

Design and Key Technology Research of Digital Assembly Finishing System for Middle and Outer Wing

Application of Turbine Blade Registration Algorithm Based on Measurement Point Cloud

Related Author

HUANG Ke

FANG Xuewei

LI Ran

LUO Qiang

ZHANG Hongkai

LAI Daogui

FANG Chunjiao

WANG Haoming

Related Institution

AECC South Industry Company Limited

Xi’an Jiaotong University

Shaanxi Cold Spray Additive Manufacturing Technology Co., Ltd

Shaanxi Key Laboratory of Friction Welding Technologies

State Key Laboratory of Solidification Processing, School of Materials Science and Engineering, Northwestern Polytechnical University

The platform construction and operation are provided by Beijing Founder electronics co., LTD 京ICP备09064830号-19 京公网安备11010802024621
It is recommended to read the content of this site in Chrome&IE9+. Please switch to extreme mode in browser 360.
Cookies We use cookies to help provide and enhance our service and tailor content. By continuing, you agree to the use of cookies.
Total Visits：34057 Visits Today：4

⁰