Microstructure and Mechanical Property of Superplastic Deformed Ti–4.5Al–3V–2Fe–2Mo Alloy Sheet

FU Mingjie; ZENG Yuansong; HAN Xiuquan; Lü Fenggong; WANG Fuxin

doi:10.16080/j.issn1671-833x.2021.01/02.076

您当前的位置：

首页 >

文章列表页 >

Microstructure and Mechanical Property of Superplastic Deformed Ti–4.5Al–3V–2Fe–2Mo Alloy Sheet

更新时间：2025-10-30

- Microstructure and Mechanical Property of Superplastic Deformed Ti–4.5Al–3V–2Fe–2Mo Alloy Sheet
- Aeronautical Manufacturing Technology Vol. 64, Issue 1/2, (2021)
- 作者机构：
  
  1. 中国航空制造技术研究院,北京,100024
  2. 塑性成形技术航空科技重点实验室,北京,100024
  3. 数字化塑性成形技术与装备北京市重点实验室,北京,100024
- 作者简介：
- 基金信息：
- DOI：10.16080/j.issn1671-833x.2021.01/02.076
  CLC：
- Published：2021
- 稿件说明：
移动端阅览
付明杰，曾元松，韩秀全，吕凤工，王富鑫. Ti–4.5Al–3V–2Fe–2Mo合金板材超塑成形组织及性能研究[J]. 航空制造技术, 2021, 64(1/2): 76-81/88. FU Mingjie, ZENG Yuansong, HAN Xiuquan, Lü Fenggong, WANG Fuxin. Microstructure and Mechanical Property of Superplastic Deformed Ti–4.5Al–3V–2Fe–2Mo Alloy Sheet. Aeronautical Manufacturing Technology, 2021, 64(1/2): 76-81/88.

FU Mingjie, ZENG Yuansong, HAN Xiuquan, et al. Microstructure and Mechanical Property of Superplastic Deformed Ti–4.5Al–3V–2Fe–2Mo Alloy Sheet[J]. Aeronautical Manufacturing Technology, 2021, 64(1/2).
付明杰，曾元松，韩秀全，吕凤工，王富鑫. Ti–4.5Al–3V–2Fe–2Mo合金板材超塑成形组织及性能研究[J]. 航空制造技术, 2021, 64(1/2): 76-81/88. FU Mingjie, ZENG Yuansong, HAN Xiuquan, Lü Fenggong, WANG Fuxin. Microstructure and Mechanical Property of Superplastic Deformed Ti–4.5Al–3V–2Fe–2Mo Alloy Sheet. Aeronautical Manufacturing Technology, 2021, 64(1/2): 76-81/88. DOI： 10.16080/j.issn1671-833x.2021.01/02.076.

FU Mingjie, ZENG Yuansong, HAN Xiuquan, et al. Microstructure and Mechanical Property of Superplastic Deformed Ti–4.5Al–3V–2Fe–2Mo Alloy Sheet[J]. Aeronautical Manufacturing Technology, 2021, 64(1/2). DOI： 10.16080/j.issn1671-833x.2021.01/02.076.

摘要

分别采用最大 m 值法和恒应变速率法对 Ti–4.5Al–3V–2Fe–2Mo 合金（SP700 钛合金）板材进行超塑拉伸，研究了 755~785℃、0.1~0.005s–1 及不同方向的单向条件下其超塑拉伸变形行为和典型件的超塑成形行为及力学性能。结果表明：SP700 钛合金具有优异的低温超塑性，采用最大 m 值法在 45° 方向、775℃变形后，获得 3110% 的最高延伸率，变形诱发晶粒长大使 SP700 钛合金抵抗颈缩的能力增加。受双向拉应力作用的锥形件，在 755℃具有最优的超塑成形工艺性，锥形件高度可达到 100mm，并且晶粒尺寸无明显变化。经 33% 超塑变形量的试样室温力学性能略高于无变形试样，其室温抗拉强度和延伸率平均值分别达到 1027MPa 和 16.8%。

Abstract

The superplasticity of Ti–4.5Al–3V–2Fe–2Mo alloy (SP700 alloy) was studied by the methods of maxium m value and constant rate under the conditions of 755~785℃

0.1~0.005s–1 and different tensile axis direction. Typical parts were formed and RT properties after superplastic forming were evaluated. The results showed SP700 alloy has excellent low temperature superplasticity with 3110% elongation at 775℃ and 45° direction with max m value tensile method. The capacity of anti-neck-shrink increased due to strain induced grains growing. The cone shape part formed at 755℃ with the highest height of 100mm under bidirectional pull stress condition

and microstructure has no significant change. RT properties of the sample with 33% deformation are 1027MPa ultrastrength and 16.8% elongation

which are little higher than those of undeformed specimens.

关键词

Keywords

references

Views

258

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Microstructure and Properties of TiC-Reinforced 7034 Aluminum Alloy Fabricated by Wire-Feed Laser Cladding

Investigation of HAZ and Its Influence of Laser Cutting 2A12 Aluminum Alloy

Microstructure and Properties of CuCrZr Fabricated by Laser Powder Bed Fusion

Microstructure and Properties of ZrC Enhanced Niobium Alloys Fabricated by Selective Laser Melting

Microstructure and Properties of Large Gap Brazing Joint of IC10 Superalloy

Related Author

CHEN Jiawen

WANG Libo

MI Gaoyang

ZENG Guang

CHAO Jingyu

MA Xiuquan

武伟超

王永军

Related Institution

School of Mechanical Science and Engineering, Huazhong University of Science and Technology

School of Materials Science and Engineering, Huazhong University of Science and Technology

School of Materials Science and Engineering, Central South University

西北工业大学现代设计与集成制造技术教育部重点实验室

西安飞机工业（集团）有限责任公司

⁰