Vibration Suppression of Thin-Walled Parts Based on Additional Mass and Eddy Current Damping

LIU Haibo; ZHANG Hongze; WANG Chengxin; MIAO Huanhuan

doi:10.16080/j.issn1671-833x.2023.03.053

您当前的位置：

首页 >

文章列表页 >

Vibration Suppression of Thin-Walled Parts Based on Additional Mass and Eddy Current Damping

更新时间：2025-10-30

- Vibration Suppression of Thin-Walled Parts Based on Additional Mass and Eddy Current Damping
- Aeronautical Manufacturing Technology Vol. 66, Issue 3, Pages: 53-60(2023)
- 作者机构：
  
  大连理工大学精密与特种加工教育部重点实验室,大连,116024
- 作者简介：
- 基金信息：
- DOI：10.16080/j.issn1671-833x.2023.03.053
  CLC：
- Published：2023
- 稿件说明：
移动端阅览
刘海波，张鸿泽，王诚鑫，苗欢欢. 基于附加质量和电涡流阻尼的薄壁件铣削振动抑制[J]. 航空制造技术, 2023, 66(3): 53-60.

LIU Haibo, ZHANG Hongze, WANG Chengxin, MIAO Huanhuan. Vibration Suppression of Thin-Walled Parts Based on Additional Mass and Eddy Current Damping[J]. Aeronautical Manufacturing Technology, 2023, 66(3): 53-60.
刘海波，张鸿泽，王诚鑫，苗欢欢. 基于附加质量和电涡流阻尼的薄壁件铣削振动抑制[J]. 航空制造技术, 2023, 66(3): 53-60. DOI： 10.16080/j.issn1671-833x.2023.03.053.

LIU Haibo, ZHANG Hongze, WANG Chengxin, MIAO Huanhuan. Vibration Suppression of Thin-Walled Parts Based on Additional Mass and Eddy Current Damping[J]. Aeronautical Manufacturing Technology, 2023, 66(3): 53-60. DOI： 10.16080/j.issn1671-833x.2023.03.053.

摘要

针对薄壁件铣削颤振问题，提出了基于附加质量和电涡流阻尼的振动抑制方法。首先建立了薄壁件铣削加工动力学模型，通过颤振稳定性分析，获得附加质量和电涡流阻尼对加工稳定域的影响规律；然后提出了薄壁件附加质量优化方法，获取最佳附加质量布局和质量占比；最后设计了一套薄壁件加工抑振装置，开展了薄壁件铣削加工试验，试验表明，当同时添加附加质量组合[15，10，15] 和电涡流阻尼时，薄壁件加工振动得到明显抑制，验证了所提出方法的抑振效果。

Abstract

Aiming at the chatter problem of milling thin-walled parts

a vibration suppression method based on additional mass and eddy current damping is proposed. Firstly

a dynamic model of milling machining of thin-walled parts is established

and the influence law of additional mass and eddy current damping on the machining stability region is obtained through flutter stability analysis; Then an optimization method for added mass of thin-walled parts is proposed to obtain the optimal added mass layout and mass proportion; Finally

a set of thin-walled parts processing vibration suppression device was designed

and the thin-walled parts milling experiment was carried out. The research results show that when the additional mass combination [15

15] and eddy current damping are added at the same time

the thinwalled workpiece machining vibration is significantly suppressed

which verifies the effectiveness of the proposed vibration suppression method.

关键词

Keywords

references

Views

121

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Effect of Pillar Size on Temperature Change and Residual Stress of Thin-Walled Titanium Alloy Lattice Structure

Research on Surface Roughness Prediction and Control Method of Laser Deposition Manufacturing Parts

Model Prediction and Experimental Study on Deposition Width of Thin-Walled Parts Manufactured by Laser Deposition in Small Molten Pools

Research on Kinematic Modeling and Automatic Trajectory Adjustment for Mirror Milling Based on Screw Theory

Tool Wear State Identification Method of Thin-Walled Parts Milling Process Driven by Digital Twin

Related Author

PENG Kai

WANG Xiaokang

LIU Hui

HU Yuheng

CAI Gaoshen

WANG Xiangming

REN Yuhang

WANG Yushi

Related Institution

浙江理工大学

AVIC Shenyang Aircraft Design and Research Institute

Key Laboratory of Fundamental Science for National Defense of Aeronautical Digital Manufacturing Process, Shenyang Aerospace University

Shenyang Aerospace University

AVIC Manufacturing Technology Institute

The platform construction and operation are provided by Beijing Founder electronics co., LTD 京ICP备09064830号-19 京公网安备11010802024621
It is recommended to read the content of this site in Chrome&IE9+. Please switch to extreme mode in browser 360.
Cookies We use cookies to help provide and enhance our service and tailor content. By continuing, you agree to the use of cookies.
Total Visits：34382 Visits Today：329

⁰