Study on Manual Electromagnetic Riveting Process and Riveting Quality of Composite Materials

YANG Yanjie; CHEN Chang; WEI Yuhao; TU Juncheng; FAN Xifeng

doi:10.16080/j.issn1671-833x.2023.23/24.043

您当前的位置：

首页 >

文章列表页 >

Study on Manual Electromagnetic Riveting Process and Riveting Quality of Composite Materials

更新时间：2025-10-30

- Study on Manual Electromagnetic Riveting Process and Riveting Quality of Composite Materials
- Aeronautical Manufacturing Technology Vol. 66, Issue 23/24, (2023)
- 作者机构：
  
  航空工业成都飞机工业（集团）有限责任公司,成都,610092
- 作者简介：
- 基金信息：
- DOI：10.16080/j.issn1671-833x.2023.23/24.043
  CLC：
- Published：2023
- 稿件说明：
移动端阅览
杨彦杰，陈昶，魏誉豪，涂俊成，樊西锋. 手工电磁铆接过程及复合材料铆接质量研究[J]. 航空制造技术, 2023, 66(23/24): 43-51. YANG Yanjie, CHEN Chang, WEI Yuhao, TU Juncheng, FAN Xifeng. Study on Manual Electromagnetic Riveting Process and Riveting Quality of Composite Materials[J]. Aeronautical Manufacturing Technology, 2023, 66(23/24): 43-51.

YANG Yanjie, CHEN Chang, WEI Yuhao, et al. Study on Manual Electromagnetic Riveting Process and Riveting Quality of Composite Materials[J]. Aeronautical Manufacturing Technology, 2023, 66(23/24).
杨彦杰，陈昶，魏誉豪，涂俊成，樊西锋. 手工电磁铆接过程及复合材料铆接质量研究[J]. 航空制造技术, 2023, 66(23/24): 43-51. YANG Yanjie, CHEN Chang, WEI Yuhao, TU Juncheng, FAN Xifeng. Study on Manual Electromagnetic Riveting Process and Riveting Quality of Composite Materials[J]. Aeronautical Manufacturing Technology, 2023, 66(23/24): 43-51. DOI： 10.16080/j.issn1671-833x.2023.23/24.043.

YANG Yanjie, CHEN Chang, WEI Yuhao, et al. Study on Manual Electromagnetic Riveting Process and Riveting Quality of Composite Materials[J]. Aeronautical Manufacturing Technology, 2023, 66(23/24). DOI： 10.16080/j.issn1671-833x.2023.23/24.043.

摘要

为研究电磁铆接技术的工艺可行性，通过工艺试验探究了手工电磁铆接工艺的可操作性，并从镦头成形、钉孔干涉以及复材损伤3个角度进行了铆接质量分析。结果表明，铝铆钉与钛铌铆钉合适的铆接电压分别为550~600 V和750~790 V。即便是在550 V电压下，电磁铆接的瞬时冲击力也可能使得操作人员不易稳定地固持铆枪和顶铁。易导致镦头斜面、零件表面碰伤及铆卡印等损伤。肌电信号分析结果表明，相比气动锤铆，电磁铆接的冲击力使得操作人员的手臂肌肉负荷增加约50%。铆接质量方面，在复材–钛合金及复材– 复材结构上，电磁铆接镦头尺寸均满足工艺要求，复合材料无损伤，且钉孔之间可产生较可靠的干涉配合，但镦头歪斜与边缘小斜面等问题限制了其应用。

Abstract

To study the processability of electromagnetic riveting technology

we explored the feasibility of manually operated electromagnetic riveting by experiments

and analyzed riveting quality through the analysis of rivet formation

the interferences between rivet and hole

as well as the damage of composites. The results show that it may be not easy for operators to hold the riveting gun and top iron stably due to the instantaneous impact force of electromagnetic riveting. Compared with pneumatic hammer riveting

the impact force of electromagnetic riveting increased the muscular load of the operator’s arm by about 50%. In addition

on composite-titanium alloy and composite-composite structures

the size of the titanium-niobium rivet upset head met process requirements without obvious cracks. In addition to no damage observed inside the composite

reliable interference fit can be formed between the nails and holes. However

the problems of skewed heading and small inclined edges of the heading limit the application of electromagnetic riveting.

关键词

Keywords

references

Views

257

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Research on Influence of Tightening Sequence and Assembly Gap on Preloading Force of Composites/Aluminum Alloy Laminated Multi-Bolt Structure

Research on Ultrasonic C-Scan Images Denoising and Super-Resolution Reconstruction for Composite Components

Contact Stress Simulation and Defect Study of Contour-Following Layups for Heat Protective Structures

A General Braiding Simulation Method for Special-Shaped Braiding Structural Parts Based on Model Reconstruction Algorithm

A Review of Preparation and Performance of High-Strength and High-Modulus Casting Mg–Li Alloy

Related Author

LIU Zhitong

AN Luling

ZHAO Cong

QU Zhengtao

XU Zhenye

LIU Zhenhao

QIAN Hengkui

JIN Shijie

Related Institution

Nanjing University of Aeromautics and Astronautics

NDT & E Laboratory, Dalian University of Technology

Key Lab of High Performance Electromagnetic Window for Aviation Science and Technology, AVIC Research Institute for Special Structures of Aeronautical Composites

Nanjing University of Aeronautics and Astronautics

College of Mechanical Engineering, Donghua University

The platform construction and operation are provided by Beijing Founder electronics co., LTD 京ICP备09064830号-19 京公网安备11010802024621
It is recommended to read the content of this site in Chrome&IE9+. Please switch to extreme mode in browser 360.
Cookies We use cookies to help provide and enhance our service and tailor content. By continuing, you agree to the use of cookies.
Total Visits：34412 Visits Today：359

⁰