Progress in Optimizing Comprehensive Performance of Hot-Press Injection Molded Ceramic Cores Through Material Design

WANG Yan; CHEN Xi; PENG Shuaiguo; ZHANG Yaozhong; LI Fei

doi:10.16080/j.issn1671-833x.25010166

您当前的位置：

首页 >

文章列表页 >

Progress in Optimizing Comprehensive Performance of Hot-Press Injection Molded Ceramic Cores Through Material Design

FORUM | 更新时间：2026-06-16

- Progress in Optimizing Comprehensive Performance of Hot-Press Injection Molded Ceramic Cores Through Material Design
- Aeronautical Manufacturing Technology Vol. 69, Issue 10, Pages: 75-88(2026)
- 作者机构：
  
  上海交通大学，上海 200240
  中国联合重型燃气轮机技术有限公司，北京 100015
- 作者简介：
- 基金信息：
- DOI：10.16080/j.issn1671-833x.25010166
  CLC： V232;TQ174
- Received：13 November 2025，
  
  Revised：2025-12-18，
  
  Accepted：26 December 2025，
  
  Published：15 May 2026
- 稿件说明：
移动端阅览
引文格式：王岩，陈曦，彭帅国，等.材料设计优化热压注成形陶瓷型芯综合性能研究进展[J].航空制造技术，2026, 69（10）：25010166.

WANG Yan, CHEN Xi, PENG Shuaiguo, et al. Progress in optimizing comprehensive performance of hot-press injection molded ceramic cores through material design[J]. Aeronautical Manufacturing Technology, 2026, 69(10): 25010166.
引文格式：王岩，陈曦，彭帅国，等.材料设计优化热压注成形陶瓷型芯综合性能研究进展[J].航空制造技术，2026, 69（10）：25010166. DOI： 10.16080/j.issn1671-833x.25010166.

WANG Yan, CHEN Xi, PENG Shuaiguo, et al. Progress in optimizing comprehensive performance of hot-press injection molded ceramic cores through material design[J]. Aeronautical Manufacturing Technology, 2026, 69(10): 25010166. DOI： 10.16080/j.issn1671-833x.25010166.

摘要

为满足高推重比发动机对涡轮叶片的苛刻要求，获得高精度与高可靠性的陶瓷型芯是制备空心叶片的关键。针对热压注成形制备陶瓷型芯存在的收缩率高、气孔率与力学性能难平衡等问题，对SiO

、Al

、MgO及Y

陶瓷型芯的相关研究进行综述。聚焦优化原料颗粒级配、调控矿化剂种类、引入高性能纤维及添加第二相材料等材料设计方法，探讨其对陶瓷型芯的收缩率、气孔率、室温/高温强度及热变形量等关键性能的影响规律和内在机理。不同材料体系对同一性能优化策略的响应程度存在显著差异，性能提升机理也不尽相同。通过对比不同材料体系与优化路径间的共性与特性，旨在为未来高性能陶瓷型芯的理性设计与工艺优化提供理论依据与技术参考。

Abstract

To meet the stringent requirements of high thrust-to-weight ratio engines for turbine blades

obtaining ceramic cores with high precision and reliability is crucial for manufacturing hollow blades. In response to issues such as high shrinkage rates and the difficulty in balancing porosity with mechanical properties in hot-press injection-molded ceramic cores

this paper provides a review of research on SiO

MgO

and Y

-based ceramic cores. Focusing on material design approaches—including optimization of raw material particle size distribution

adjustment of mineralizer types

introduction of high-performance fibers

and incorporation of second phase materials—the influence of these strategies on key properties such as shrinkage

porosity

room- and high-temperature strength

and thermal deformation is discussed

along with the underlying mechanisms. The response of different ceramic core systems to the same strategy varies significantly

and the mechanisms for performance enhancement are not universal. By comparing the commonalities and specific characteristics of different material systems and optimization routes

this review aims to offer a theoretical foundation and technical reference for the rational design and process optimization of future high-performance ceram

ic cores.

关键词

Keywords

references

刘砚飞，钟燕，陶稀鹏，等.镍基单晶高温合金/热障涂层体系的应用研究进展[J].材料工程，2025, 53(9): 1-10.

LIU Yanfei, ZHONG Yan, TAO Xipeng, et al. Research progress in application of nickel-based single crystal superalloy/thermal barrier coating system[J]. Journal of Materials Engineering, 2025, 53(9): 1-10.

冷玉潇，曹铁山，陈家万，等.航空发动机用镍基单晶高温合金涡轮叶片服役后的显微组织损伤[J].机械工程材料，2025, 49(2):34-42.

LENG Yuxiao, CAO Tieshan, CHEN Jiawan, et al. Microstructure damage of nickel-based single crystal superalloy turbine blade for aircraft engine after service[J]. Materials for Mechanical Engineering, 2025, 49(2): 34-42.

肖强，曾献城，魏群.航空发动机涡轮叶片气膜孔制备仿真与试验研究[J].航空制造技术，2025, 68(14): 34-41.

XIAO Qiang, ZENG Xiancheng, WEI Qun. Simulation and experimental study on preparation of air film holes for aero-engine turbine blades[J]. Aeronautical Manufacturing Technology, 2025, 68(14): 34-41.

由儒全，权胜，陈文彬，等.气膜孔孔径变化对涡轮叶片全表面冷却特性影响研究[J].航空动力学报，2025, 40(8): 20-28.

YOU Ruquan, QUAN Sheng, CHEN Wenbin, et al. Effects of film hole diameter variations on overall cooling performance of a rotating turbine blade[J]. Journal of Aerospace Power, 2025, 40(8): 20-28.

孔祥灿，张子卿，朱俊强，等.航空发动机气冷涡轮叶片冷却结构研究进展[J].推进技术，2022, 43(5): 1-23.

KONG Xiangcan, ZHANG Ziqing, ZHU Junqiang, et al. Research progress on cooling structure of aeroengine air-cooled turbine blade[J]. Journal of Propulsion Technology, 2022, 43(5):1-23.

张攀，汪东红，肖程波，等.航空发动机高温合金铸件精密成形研究进展[J].航空制造技术，2025, 68(18): 162-172.

ZHANG Pan, WANG Donghong, XIAO Chengbo, et al. Research progress on precision forming of aero-engine superalloy castings[J]. Aeronautical Manufacturing Technology, 2025, 68(18): 162-172.

张鹏飞，张林嘉，周瑜，等.钛合金精密铸造技术在航空航天领域的应用进展[J].航空制造技术，2025, 68(7): 22-36.

ZHANG Pengfei, ZHANG Linjia, ZHOU Yu, et al. Application progress of titanium alloys investment casting in aerospace industry[J]. Aeronautical Manufacturing Technology, 2025, 68(7): 22-36.

张金，张巍，金磊，等.熔模铸造用陶瓷型芯材料的研究应用现状及展望[J].特种铸造及有色合金，2024, 44(12): 1687-1696.

ZHANG Jin, ZHANG Wei, JIN Lei, et al. Research status and prospects on ceramic core materials for investment casting[J]. Special Casting& Nonferrous Alloys, 2024, 44(12): 1687-1696.

许西庆，杨永康，李杰，等.空心叶片铸造用陶瓷型芯的3D打印及性能调控研究进展[J].硅酸盐学报，2023, 51(6): 1583-1594.

XU Xiqing, YANG Yongkang, LI Jie, et al. Research progress on 3D printing and performance optimization of ceramic cores for hollow blade casting[J]. Journal of the Chinese Ceramic Society, 2023, 51(6): 1583-1594.

陈超越，殷宇豪，徐松哲，等.航空发动机叶片用陶瓷型芯的光固化增材制造研究现状[J].航空制造技术，2022, 65(1/2): 67-76.

CHEN Chaoyue, YIN Yuhao, XU Songzhe, et al. Research status of lithography-based additive manufacturing of ceramic cores for aero-engine blade[J]. Aeronautical Manufacturing Technology, 2022, 65(1/2): 67-76.

许西庆，李世元，杨永康，等.氧化铝纤维强化陶瓷型芯的3D打印及尺寸精度控制[J].机械工程学报，2025, 61(5): 323-329.

XU Xiqing, LI Shiyuan, YANG Yongkang, et al. 3D printing and dimensional accuracy control of ceramic cores reinforced by alumina fibers[J]. Journal of Mechanical Engineering, 2025, 61(5):323-329.

江红涛，杨昕昊，王秀峰.黏结剂喷射制备陶瓷型芯抗弯强度、尺寸精度及表面质量影响因素的研究进展[J].机械工程材料，2024, 48(5): 8-14.

JIANG Hongtao, YANG Xinhao, WANG Xiufeng. Research progress on factors affecting bending strength, dimensional accuracy and surface quality of ceramic cores by binder jetting[J]. Materials for Mechanical Engineering, 2024, 48(5): 8-14.

潘正武.原料颗粒级配和矿化剂对镁基陶瓷型芯性能影响的研究[D].南京：东南大学，2021.

PAN Zhengwu. Study on the influence of raw material particle gradation and mineralizer on the properities of magnesium-based ceramic core[D]. Nanjing: Southeast University, 2021.

任士平，张力，李帅鹏，等.高尺寸稳定性的MgAl 2 O 4 /MgO复合陶瓷型芯的制备[J ] .有色金属工程，2023, 13(9): 12-22.

REN Shiping, ZHANG Li, LI Shuaipeng, et al. Preparation of MgAl 2 O 4 /MgO-based composite ceramic core with high dimensional stability[J ] . Nonferrous Metals Engineering, 2023, 13(9):12-22.

陈晓燕，肖旅，余建波，等.熔模铸造高温合金与陶瓷材料界面反应研究进展[J].特种铸造及有色合金，2016, 36(8): 844-848.

CHEN Xiaoyan, XIAO Lü, YU Jianbo, et al. Research status of the interface reactions between superalloys and ceramic materials in investment casting[J]. Special Casting & Nonferrous Alloys, 2016, 36(8): 844-848.

赵代银，何建，伍林，等.陶瓷型芯在高温合金熔模铸造中的应用技术[J].特种铸造及有色合金，2020, 40(9): 999-1003.

ZHAO Daiyin, HE Jian, WU Lin, et al. Application technology of ceramic core in investment casting of super alloy[J]. Special Casting & Nonferrous Alloys, 2020, 40(9): 999-1003.

胡可辉，吕志刚，陆宽，等.复杂陶瓷型芯增材制造及浇注工艺验证[J].机械工程学报，2021, 57(3): 227-234.

HU Kehui, LÜ Zhigang, LU Kuan, et al. Additive manufacturing of complex ceramic cores and verification of casting process[J]. Journal of Mechanical Engineering, 2021, 57(3): 227-234.

YANG Z G, YIN Z Q, ZHAO Z J, et al. Microstructure and properties of SiO 2 based ceramic cores with ball-shaped powders by the pre ceramic polymer technique in N2 atmosphere[J ] . Materials Chemistry and Physics, 2020, 243: 122609.

戴睿卿，玄伟东，张强，等.定向高温合金UGTC47与硅基陶瓷型芯界面反应研究[J].特种铸造及有色合金，2025, 45(1): 112-117.

DAI Ruiqing, XUAN Weidong, ZHANG Qiang, et al. Interfacial reaction between UGTC47 directional superalloy and silicon-based ceramic core[J]. Special Casting & Nonferrous Alloys, 2025, 45(1): 112-117.

罗凌，芦刚，严青松，等.氧化铝基陶瓷型芯溶失性的研究进展[J].特种铸造及有色合金，2021, 41(3): 305-309.

LUO Ling, LU Gang, YAN Qingsong, et al. Research progress in alumina-based ceramic cores' Dissolution[J]. Special Casting & Nonferrous Alloys, 2021, 41(3): 305-309.

芦刚，查军辉，严青松，等.PA66纤维含量对多孔铝基陶瓷型芯气孔率的影响[J].材料工程，2020, 48(7): 170-175.

LU Gang, ZHA Junhui, YAN Qingsong, et al. Influence of PA66 fiber content on porosity ofporous aluminum based ceramic core[J]. Journal of Materials Engineering, 2020, 48(7): 170-175.

罗龙华.多孔MgO-MgAl 2 O 4 复合镁基陶瓷型芯的制备及性能研究[D ] .南昌：南昌航空大学，2024.

LUO Longhua. Study of preparation and properties in porous MgO-MgAl 2 O 4 composite magnesium based ceramic core[D ] . Nanchang:Nanchang Hangkong University, 2024.

李明，康永旺，郭丰伟，等.Nb-Si合金高温熔体与型壳和型芯的界面反应[J].铸造，2023, 72(6): 648-653.

LI Ming, KANG Yongwang, GUO Fengwei, et al. Interface reactions between ultra-high temperature ceramic shell/core and molten Nb-Si alloy[J]. Foundry, 2023, 72(6): 648-653.

MUSTAPA N B, AHMAD R, IBRAHIM W M W, et al. Effect of sintering mechanism towards crystallization of geopolymer ceramic—a review[J]. Materials, 2023, 16(11):4103.

CHAIM R, LEVIN M, SHLAYER A, et al. Sintering and densification of nanocrystalline ceramic oxide powders: A review[J]. Advances in Applied Ceramics, 2008, 107(3): 159-169.

牛书鑫，骆宇时，李鑫，等.陶瓷型芯颗粒级配控制及综合性能评定[J].铸造，2025, 74(3): 350-356.

NIU Shuxin, LUO Yushi, LI Xin, et al. Evaluation on comprehensive performance of ceramic cores with controlled particle grading[J]. Foundry, 2025, 74(3): 350-356.

陆丽芳，张弘毅，武振飞.熔融石英粉体级配对硅基陶瓷型芯性能的影响[J].江苏陶瓷，2020, 53(4): 28-29, 36.

LU Lifang, ZHANG Hongyi, WU Zhenfei. Effect of Shi Ying Powder gradation on properties of silicon-based ceramic core[J]. Jiangsu Ceramics, 2020, 53(4): 28-29, 36.

XU X Q, NIU S X, WANG X G, et al. Fabrication and casting simulation of composite ceramic cores with silica nanopowders[J]. Ceramics International, 2019, 45(15): 19283-19288.

覃业霞，张睿，杜爱兵，等.粉料粒度对氧化铝基陶瓷型芯材料性能的影响[J].稀有金属材料与工程，2007, 36(S1): 711-713.

QIN Yexia, ZHANG Rui, DU Aibing, et al. Effect of particle size on properties of aluminabased ceramic cores[J]. Rare Metal Materials and Engineering, 2007, 36(S1): 711-713.

于子豪，杨治刚，秦国强，等.稀土氧化钇基陶瓷型芯材料的制备研究[J].铸造，2020, 69(6): 612-616.

YU Zihao, YANG Zhigang, QIN Guoqiang, et al. Preparation of rare earth yttrium oxide-based ceramic core material[J]. Foundry, 2020, 69(6): 612-616.

陈天赐，李乔磊，张辉，等.矿化剂对陶瓷型芯性能的影响[J].铸造，2022, 71(10):1262-1270.

CHEN Tianci, LI Qiaolei, ZHANG Hui, et al. Effect of mineralizers on properties of ceramic core[J]. Foundry, 2022, 71(10): 1262-1270.

张强，丁方政，玄伟东，等.矿化剂对陶瓷型芯组织和性能调控研究进展[J].特种铸造及有色合金，2025, 45(2): 179-186.

ZHANG Qiang, DING Fangzheng, XUAN Weidong, et al. Progress in mineralizer regulating microstrcture and properties of ceramic cores[J]. Special Casting & Nonferrous Alloys, 2025, 45(2):179-186.

范红娜，许西庆，李鑫，等.氧化铝改性硅基陶瓷型芯制备及结晶动力学[J].材料工程，2024, 52(5): 212-217.

FAN Hongna, XU Xiqing, LI Xin, et al. Preparation and crystallization kinetics of silicabased ceramic cores modified by alumina[J]. Journal of Materials Engineering, 2024, 52(5):212-217.

PAN Z P, GUO J Z, LI S M, et al. Investigation of microstructure evolution and properties in silica-based ceramic cores with alumina as a mineralizer[J]. International Journal of Applied Ceramic Technology, 2023, 20(3):2009-2018.

陈昊，李鑫，牛书鑫，等.氧化硅/莫来石陶瓷型芯的析晶行为及性能研究[J].人工晶体学报，2020, 49(5): 902-907.

CHEN Hao, LI Xin, NIU Shuxin, et al. Crystallization behavior and properties of silica/mullite ceramic cores[J]. Journal of Synthetic Crystals, 2020, 49(5): 902-907.

李寒松，玄伟东，潘文轩，等.电熔莫来石含量对硅基陶瓷型芯性能的影响[J].铸造，2020, 69(8): 861-865.

LI Hansong, XUAN Weidong, PAN Wenxuan, et al. Effect of fused mullite content on properties of silicon-based ceramic cores[J].Foundry, 2020, 69(8): 861-865.

吴笑非，李鑫，许西庆，等.不同粒度莫来石粉改性硅基陶瓷型芯的制备及性能[J].航空材料学报，2021, 41(4): 128-133.

WU Xiaofei, LI Xin, XU Xiqing, et al. Fabrication and properties of silica-based ceramic cores modified by mullite powders with different particle sizes[J]. Journal of Aeronautical Materials, 2021, 41(4): 128-133.

刘泳鸿，玄伟东，张强，等.碳化硼对硅基陶瓷型芯性能的影响研究[J].铸造，2024, 73(4): 532-539.

LIU Yonghong, XUAN Weidong, ZHANG Qiang, et al. Effect of boron carbide on properties of silicon-based ceramic core[J]. Foundry, 2024, 73(4): 532-539.

曹咏梅，易仁杰，刘强，等.电熔氧化钇含量对硅基陶瓷型芯性能的影响[J].铸造，2025, 74(3): 365-369.

CAO Yongmei, YI Renjie, LIU Qiang, et al. Effect of the fused yttria content on the properties of silicon-based ceramic core[J]. Foundry, 2025, 74(3): 365-369.

PAN Z P, GUO J Z, LI S M, et al. Experimental study on high temperature performances of silica-based ceramic core for single crystal turbine blades[J]. Ceramics International, 2022, 48(1): 548-555.

YANG Z G, ZHAO Z J, YU J B, et al. Effect of silicone resin as precursor and binder on the properties of alumina-based ceramic cores using ball-shaped powders[J]. Ceramics International, 2019, 45(2): 2170-2177.

杨志彬，张阳，蒲发源，等.液态硅树脂对氧化铝基陶瓷型芯性能的影响[J].中国材料进展，2021, 40(7): 535-541.

YANG Zhibin, ZHANG Yang, PU Fayuan, et al. Effect of liquid silicone resin on the properties of Al 2 O 3 based ceramic core[J ] . Materials China, 2021, 40(7): 535-541.

贺康兴，姜卫国，毛萍莉.石英玻璃粉含量对氧化镁基陶瓷型芯性能的影响[J].铸造，2024, 73(5): 668-676.

HE Kangxing, JIANG Weiguo, MAO Pingli. Effect of fused silica powder content on the properties of MgO-based ceramic core[J]. Foundry, 2024, 73(5): 668-676.

周宇豪，玄伟东，段方苗，等.电熔刚玉对硅基陶瓷型芯性能的影响[J].稀有金属材料与工程，2023, 52(4): 1396-1402.

ZHOU Yuhao, XUAN Weidong, DUAN Fangmiao, et al. Effect of fused corundum on properties of silicon-based ceramic core[J]. Rare Metal Materials and Engineering, 2023, 52(4):1396-1402.

李彪，娄延春，于波，等.添加锆英粉矿化剂的氧化铝基陶瓷型芯试验研究[J].铸造，2020, 69(8): 853-860.

LI Biao, LOU Yanchun, YU Bo, et al. Experimental study of alumina-based ceramic cores mineralized by zircon powder[J]. Foundry, 2020, 69(8): 853-860.

马昕，刘海韬，孙逊.连续纤维增强陶瓷基复合材料连接件的研究进展[J].材料工程，2023, 51(8): 1-11.

MA Xin, LIU Haitao, SUN Xun. Research progress in continuous fiber reinforced ceramic matrix composite joints[J]. Journal of Materials Engineering, 2023, 51(8): 1-11.

商剑钊，吴小飞，曹晔洁，等.连续纤维增强碳化硅陶瓷基复合材料低成本制备工艺研究进展[J].材料工程，2025, 53(1): 15-27.

SHANG Jianzhao, WU Xiaofei, CAO Yejie, et al. Research progress in low-cost preparation process of continuous fiber-reinforced silicon carbide ceramic matrix composites[J]. Journal of Materials Engineering, 2025, 53(1): 15-27.

李毅鹏，刘孝福，娄延春，等.纤维增强技术在熔模铸造陶瓷型芯的应用研究[C]//第十九届中国铸造协会年会.天津，2023: 190-194.

LI Yipeng, LIU Xiaofu, LOU Yanchun, et al. Application of fiber reinforced technology in investment casting ceramic core[C]//The 19th Annual Conference of China Foundry Association. Tianjin, 2023: 190-194.

芦刚，于航，严青松，等.Al 2 O 3 纤维对SiO 2 基陶瓷型芯的烧缩阻滞[J ] .复合材料学报，2018, 35(1): 168-172.

LU Gang, YU Hang, YAN Qingsong, et al. Effect of Al 2 O 3 fiber on shrinkage blocking of SiO 2 matrix ceramic core[J ] . Acta Materiae Compositae Sinica, 2018, 35(1): 168-172.

肖祖德，玄伟东，段方苗，等.石英纤维对氧化硅陶瓷型芯性能的影响[J].铸造，2021, 70(9): 1072-1079.

XIAO Zude, XUAN Weidong, DUAN Fangmiao, et al. Effect of silica fibers on properties of silica ceramic cores[J]. Foundry, 2021, 70(9):1072-1079.

杨建，玄伟东，周宇豪，等.硅酸铝纤维对氧化硅陶瓷型芯性能的影响[J].铸造，2023, 72(3): 294-300.

YANG Jian, XUAN Weidong, ZHOU Yuhao, et al. Effect of aluminum silicate fibers on properties of silica ceramic core[J]. Foundry, 2023, 72(3): 294-300.

陈义斯，芦刚，严青松，等.气氛烧结短切碳纤维增强硅基陶瓷型芯的致密化行为[J].复合材料学报，2022, 39(5): 2412-2420.

CHEN Yisi, LU Gang, YAN Qingsong,et al. Densification behavior in short carbon fiber reinforced silica-based ceramic cores via atmosphere sintering[J]. Acta Materiae Compositae Sinica, 2022, 39(5): 2412-2420.

李毅鹏，娄延春，刘孝福，等.氧化锆纤维对氧化硅陶瓷型芯性能的影响[J].铸造，2023, 72(5): 564-569.

LI Yipeng, LOU Yanchun, LIU Xiaofu, et al. Influence of zirconia fiber on properties of silica ceramic cores[J]. Foundry, 2023, 72(5): 564-569.

牛书鑫，刘智鹏，周婷婷，等.基于多种莫来石纤维的硅基陶瓷型芯增强机制及性能研究[J].航空制造技术，2023, 66(19): 36-40, 47.

NIU Shuxin, LIU Zhipeng, ZHOU Tingting, et al. Reinforcing mechanism and property investigation of silica-based ceramic cores based on different mullite fibers[J]. Aeronautical Manufacturing Technology, 2023, 66(19): 36-40, 47.

田国强，闫学伟.Al 2 O 3 纤维改善Al 2 O 3 基陶瓷型芯高温强度和烧结收缩[J ] .中国陶瓷，2021, 57(3): 18-23.

TIAN Guoqiang, YAN Xuewei. Improvement of high-temperature strength and sintering shrinkage of Al 2 O 3 -based ceramic core by adding Al 2 O 3 fiber[J ] . China Ceramics, 2021, 57(3): 18-23.

芦刚，罗龙华，陈晓，等.有机-无机混杂纤维改性氧化铝基陶瓷型芯孔隙-强度协同强化机制[J].硅酸盐学报，2024, 52(1): 180-188.

LU Gang, LUO Longhua, CHEN Xiao, et al. Organic-inorganic hybrid fibers modified aluminabased ceramic core with synergistic enhancing porosity and strength[J]. Journal of the Chinese Ceramic Society, 2024, 52(1): 180-188.

NIU S X, LIU Z P, LUO Y S, et al. Reinforcement of silica-based ceramic cores based on amorphous and polycrystalline mullite fibers[J]. Ceramics International, 2023, 49(19):31378-31384.

张俊敏，蔡飞燕，靳喜海，等.连续纤维增强陶瓷基复合材料研究与应用进展[J].陶瓷学报，2023, 44(2): 195-207.

ZHANG Junmin, CAI Feiyan, JIN Xihai, et al. Progress in research and application of continuous fiber reinforced ceramic matrix composites[J]. Journal of Ceramics, 2023, 44(2):195-207.

李鑫，牛书鑫，姚建省，等.金属Al粉对氧化硅基陶瓷型芯的性能及组织的影响[J].无机材料学报，2019, 34(2): 207-212.

LI Xin, NIU Shuxin, YAO Jiansheng, et al. Effect of Al powder on property and microstructure of silica-based ceramic core[J]. Journal of Inorganic Materials, 2019, 34(2): 207-212.

唐世艳，樊自田，刘鑫旺，等.基于Al粉成孔作用制备多孔氧化铝陶瓷型芯[J].华中科技大学学报(自然科学版), 2017, 45(4): 34-38.

TANG Shiyan, FAN Zitian, LIU Xinwang, et al. Fabrication of porous alumina-based ceramic core using aluminium as pore-forming agent[J]. Journal of Huazhong University of Science and Technology (Nature Science Edition), 2017, 45(4):34-38.

芦刚，吴谦，陈晓，等.Al粉含量对Y 2 O 3 基陶瓷型芯性能及组织的影响[J ] .复合材料学报，2024, 41(8): 4366-4374.

LU Gang, WU Qian, CHEN Xiao, et al. Effect of Al powder content on the properties and microstructure of Y 2 O 3 -based ceramic core[J ] . Acta Materiae Compositae Sinica, 2024, 41(8):4366-4374.

XUAN W D, ZHANG Q, SONG H R, et al. Improved mechanical properties and dimensional accuracy of silica-based ceramic cores by Si 3 N 4 addition[J ] . Ceramics International, 2024, 50(14): 25730-25737.

Views

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Research Progress on Precision Forming of Aero-Engine Superalloy Castings

A High-Temperature Large-Strain Optical Fiber Sensor Based on “8” Shaped Spring Structure

Research on Wax Mold Integrated Preparation Technology for Large Titanium Alloy Intermediate Casing

Research on Visual Measurement Techniques for Grinding Thickness of Thermal Barrier Coatings on Aero-Engine Turbine Blades

Research Status of Lithography-Based Additive Manufacturing of Ceramic Cores for Aero-Engine Blade

Related Author

SUN Baode

ZHANG Pan

WANG Donghong

XIAO Chengbo

ZHOU Leyao

LEI Sixiong

ZHENG Xing

TAN Qingbiao

Related Institution

上海交通大学材料科学与工程学院上海市先进高温材料及其精密成形重点实验室

中国航发北京航空材料研究院先进高温结构材料重点实验室

中国航发南方工业有限公司

浙江省机电设计研究院有限公司

Wuhan University of Technology

The platform construction and operation are provided by Beijing Founder electronics co., LTD 京ICP备09064830号-19 京公网安备11010802024621
It is recommended to read the content of this site in Chrome&IE9+. Please switch to extreme mode in browser 360.
Cookies We use cookies to help provide and enhance our service and tailor content. By continuing, you agree to the use of cookies.
Total Visits：42763 Visits Today：1

⁰