Study on Microstructure and Properties of TiCN Composite Coatings Prepared by Reactive Plasma Spraying

FU Guanya; QIN Yanfang; ZHU Lingyan; HE Jining; JIAO Qi

doi:10.16080/j.issn1671–833x.2019.03.055

您当前的位置：

首页 >

文章列表页 >

Study on Microstructure and Properties of TiCN Composite Coatings Prepared by Reactive Plasma Spraying

更新时间：2025-10-30

- Study on Microstructure and Properties of TiCN Composite Coatings Prepared by Reactive Plasma Spraying
- Aeronautical Manufacturing Technology Vol. 62, Issue 3, Pages: 55-61(2019)
- 作者机构：
  
  1. 河北工业大学材料科学与工程学院,天津,300130
  2. 河北工业大学天津市层状材料制备与界面控制重点实验室,天津,300130
- 作者简介：
- 基金信息：
- DOI：10.16080/j.issn1671–833x.2019.03.055
  CLC：
- Published：2019
- 稿件说明：
移动端阅览
付冠亚，秦艳芳，朱玲艳，何继宁，焦琪. 反应等离子喷涂TiCN涂层显微结构与性能研究[J]. 航空制造技术, 2019, 62(3): 55-61.

FU Guanya, QIN Yanfang, ZHU Lingyan, HE Jining, JIAO Qi. Study on Microstructure and Properties of TiCN Composite Coatings Prepared by Reactive Plasma Spraying. Aeronautical Manufacturing Technology, 2019, 62(3): 55-61.
付冠亚，秦艳芳，朱玲艳，何继宁，焦琪. 反应等离子喷涂TiCN涂层显微结构与性能研究[J]. 航空制造技术, 2019, 62(3): 55-61. DOI： 10.16080/j.issn1671–833x.2019.03.055.

FU Guanya, QIN Yanfang, ZHU Lingyan, HE Jining, JIAO Qi. Study on Microstructure and Properties of TiCN Composite Coatings Prepared by Reactive Plasma Spraying. Aeronautical Manufacturing Technology, 2019, 62(3): 55-61. DOI： 10.16080/j.issn1671–833x.2019.03.055.

摘要

利用反应等离子喷涂制备了TiCN 涂层，并采用扫描电镜、X– 射线衍射仪和X– 射线光谱分析了涂层的显微结构，采用显微硬度计、万能试验机和环–块式摩擦磨损试验机测定了涂层的机械性能和摩擦磨损性能。结果表明：涂层主相为TiC

0.7

0.3

和TiN，同时存在少量不定性石墨相和CN

相。由于大气喷涂的氧化，形成少量Ti

O。涂层为典型热喷涂铺展形貌，涂层与基体具有良好的结合性。TiCN涂层的显微硬度均在1000HV

0.2

以上，远高于基体和黏结层硬度。由于涂层H

大于0.1，具有较强抵抗塑性变形能力和耐磨性。

Abstract

The TiCN coating were successfully fabricated by reactive plasma spraying. The microstructure of coating was characterized by scanning electron micrograph (SEM)

X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS). The mechanical and tribological properties of coatings were evaluated by Vickers microhardness tests

nanoindentation tester and block-on-ring tribometer. Results showed that the main phases are TiC

0.7

0.3

and TiN with some amount of amorphous graphite and CN

phase. There are some Ti

O due to the plasm spraying carried out in atmosphere. The coating exhibits typical thermal spray spreading out morphology and a good bonding status between the coating and substrate w

as obtained. The microhardness value of coating still exceeds 1000HV

0.2

which is higher than that of substrate and bond coat. Due to the H

of coating is greater than 0.1

it indicated that TiCN coating possessed a high resistance of plastic deformation and excellent wear resistance.

关键词

Keywords

references

Views

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Strength Design and Optimization of Aviation Filter Assembly Based on CF/PEEK Composite

Modulation of Pore Structure and Properties in Phenolic Aerogels by Cationic Polyelectrolytes

Research Progress on Matrix Composition Regulation of SiC/SiC Composites

Electromechanical Behavior of Open-Hole Three-Dimensional Angle-Interlock Woven Carbon Fiber Reinforced Polymer Under Tensile Loading

Dynamic Measurement Method for Shaft Deflection Angles in Helicopter Drive Systems

Related Author

No data

Related Institution

No data

The platform construction and operation are provided by Beijing Founder electronics co., LTD 京ICP备09064830号-19 京公网安备11010802024621
It is recommended to read the content of this site in Chrome&IE9+. Please switch to extreme mode in browser 360.
Cookies We use cookies to help provide and enhance our service and tailor content. By continuing, you agree to the use of cookies.
Total Visits：34526 Visits Today：4

⁰