Study on Electrochemical Discharge Machining of Micro-Groove on Pure Tungsten

YU Hao; LIU Guixian; ZHANG Yongjun; ZHOU Zuolin

doi:10.16080/j.issn1671–833x.2019.11.047

您当前的位置：

首页 >

文章列表页 >

Study on Electrochemical Discharge Machining of Micro-Groove on Pure Tungsten

更新时间：2025-10-30

- Study on Electrochemical Discharge Machining of Micro-Groove on Pure Tungsten
- Aeronautical Manufacturing Technology Vol. 62, Issue 11, Pages: 47-54(2019)
- 作者机构：
  
  1. 广东工业大学机电工程学院,广州,510006
  2. 广州市非传统制造技术及装备重点实验室,广州,510006
- 作者简介：
- 基金信息：
- DOI：10.16080/j.issn1671–833x.2019.11.047
  CLC：
- Published：2019
- 稿件说明：
移动端阅览
余浩，刘桂贤，张永俊，周佐霖. 纯钨材料环形微槽电解电火花加工特性研究[J]. 航空制造技术, 2019, 62(11): 47-54.

YU Hao, LIU Guixian, ZHANG Yongjun, ZHOU Zuolin. Study on Electrochemical Discharge Machining of Micro-Groove on Pure Tungsten. Aeronautical Manufacturing Technology, 2019, 62(11): 47-54.
余浩，刘桂贤，张永俊，周佐霖. 纯钨材料环形微槽电解电火花加工特性研究[J]. 航空制造技术, 2019, 62(11): 47-54. DOI： 10.16080/j.issn1671–833x.2019.11.047.

YU Hao, LIU Guixian, ZHANG Yongjun, ZHOU Zuolin. Study on Electrochemical Discharge Machining of Micro-Groove on Pure Tungsten. Aeronautical Manufacturing Technology, 2019, 62(11): 47-54. DOI： 10.16080/j.issn1671–833x.2019.11.047.

摘要

为解决氙灯钨阳极表面密集环形微槽加工的技术问题，提出了采用RC 电源，在超低电导率下电解电火花加工纯钨表面微沟槽的方法。研究在RC 电源下，不同电解液类型下的电解电火花加工特性。首先，通过电化学工作站测量纯钨材料在不同电解液类型下的极化曲线，分析不同电解液类型的初腐蚀电位。为研究加工过程形成的气泡对加工的影响规律，通过高速摄像仪对不同工艺条件下加工区域的气泡形成与分布进行观察。最后，采用自主研制的试验装置开展了纯钨棒材表面环形微沟槽电解电火花加工工艺试验，分析工作液成分、电导率、转速和电压不同参数对加工特性的影响规律。在极间电压60V，转速500r/min，电导率为50μS/cm 的NaOH 电解液下加工了槽宽为50.97μm，槽深为17.31μm 的微沟槽结构。

Abstract

In order to solve the technical problem of dense micro grooves on the surface of xenon lamp tungsten anode

a method of electrochemical discharge machining (ECDM) of micro grooves on pure tungsten at low conductivity electrolyte was proposed

and RC power supply was applied into the process. The characteristics of ECDM with different electrolyte under RC power supply were studied. Firstly

the polarization curves of pure tungsten materials under different electrolytes were measured by electrochemical workstation

and the open circuit potential at different electrolytes was analyzed. In order to study the influence of the bubbles distribution during the processing

the bubbles formation and distribution in the machining area under different experimental conditions were observed by high-speed camera. Finally

the process of ECDM of micro-groove on the surface of pure tungsten rod was carried out with self-developed test device. The effects of electrolyte type

conductivity

rotational speed and inter electrode voltage on the machining characteristics were analyzed. Under 50μS/cm NaOH solution with an inter electrode voltage of 60V and a rotating speed of 500r/min

the micro groove with width is 50.97μm and the depth is 17.31μm was obtained by ECDM.

关键词

Keywords

references

Views

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Research Progress on Matrix Composition Regulation of SiC/SiC Composites

Research on Ultrasonic Vibration-Assisted Milling and Grinding of Ceramic Matrix Composites

Dynamic Measurement Method for Shaft Deflection Angles in Helicopter Drive Systems

Research Progress on Ceramic Matrix Composites for Aviation Applications

Research Progress on In-Plane Shear Mechanical Behavior of Silicon Carbide Ceramic Matrix Composites

Related Author

No data

Related Institution

No data

The platform construction and operation are provided by Beijing Founder electronics co., LTD 京ICP备09064830号-19 京公网安备11010802024621
It is recommended to read the content of this site in Chrome&IE9+. Please switch to extreme mode in browser 360.
Cookies We use cookies to help provide and enhance our service and tailor content. By continuing, you agree to the use of cookies.
Total Visits：34528 Visits Today：6

⁰