30CrMnSiNi2A 钢电子束焊接头的疲劳裂纹扩展特性研究

张颖云; 胡生双; 朱增辉; 郑超; 龙健; 张林杰

doi:10.16080/j.issn1671-833x.2022.08.113

您当前的位置：

首页 >

文章列表页 >

30CrMnSiNi2A 钢电子束焊接头的疲劳裂纹扩展特性研究

研究论文 | 更新时间：2025-10-30

- 30CrMnSiNi2A 钢电子束焊接头的疲劳裂纹扩展特性研究
- 航空制造技术 2022年65卷第8期页码：113-118
- 作者机构：
  
  1. 中航西安飞机工业集团股份有限公司,西安,710089
  2. 西安交通大学金属材料强度国家重点实验室,西安,710049
- 作者简介：
- 基金信息：
- DOI：10.16080/j.issn1671-833x.2022.08.113
  中图分类号：
- 纸质出版：2022
- 稿件说明：
移动端阅览
张颖云，胡生双，朱增辉，郑超，龙健，张林杰 . 30CrMnSiNi2A 钢电子束焊接头的疲劳裂纹扩展特性研究[J]. 航空制造技术, 2022, 65(8): 113-118.

ZHANG Yingyun，HU Shengshuang，ZHU Zenghui，ZHENG Chao，LONG Jian，ZHANG Linjie . Study on Fatigue Crack Propagation Characteristics of Electron Beam Welded Joint of 30CrMnSiNi2A Steel. Aeronautical Manufacturing Technology, 2022, 65(8): 113-118.
张颖云，胡生双，朱增辉，郑超，龙健，张林杰 . 30CrMnSiNi2A 钢电子束焊接头的疲劳裂纹扩展特性研究[J]. 航空制造技术, 2022, 65(8): 113-118. DOI： 10.16080/j.issn1671-833x.2022.08.113.

ZHANG Yingyun，HU Shengshuang，ZHU Zenghui，ZHENG Chao，LONG Jian，ZHANG Linjie . Study on Fatigue Crack Propagation Characteristics of Electron Beam Welded Joint of 30CrMnSiNi2A Steel. Aeronautical Manufacturing Technology, 2022, 65(8): 113-118. DOI： 10.16080/j.issn1671-833x.2022.08.113.

摘要

比较了26mm厚30CrMnSiNi2A超高强度钢电子束焊接头的母材、热影响区和焊缝区的疲劳裂纹扩展速率。试验结果表明，母材的抗疲劳裂纹扩展性能最好；热影响区抗疲劳裂纹扩展性能相对较弱；焊缝区的抗疲劳裂纹扩展性能接近母材。分别观察了母材、热影响区和焊缝区 3 个区域疲劳试样的断口形貌，发现接头各区域均呈现多源启裂特征，在稳定扩展区域和快速扩展区域均发现疲劳条纹。在接头 3 个区域最后失稳断裂区域均发现大量韧窝，呈现韧性断裂特征。通过光镜和扫描电镜观察了接头 3 个区域的显微组织特征，发现接头各区域在光镜和扫描电镜下的显微组织差异较小，均为回火马氏体。

Abstract

This paper compared the fatigue crack growth rate of the base metal (BM)

heat affect zone (HAZ) and weld metal (WM) of the ultra-high strength steel electron beam welded joint of 26mm thick 30CrMnSiNi2A. The experimental results showed that the fatigue crack growth resistance of the BM was the best; HAZ was relatively weak; WM was closed to that of the BM. The fractured morphologies of BM

HAZ and WM fatigue samples were observed. It was found that multi-source crack initiation was found in each region of the joint

fatigue striations were found in the stable and fast crack propagation area

and a large number of dimples were found in fractured zone of the three regions of the joint

presented ductile fracture characteristics. The microstructure characteristics of the three regions of the joint were observed by optical microscope and scanning electron microscope. It was found that the differences between the microstructure of each region of the joint were slightly

and all of them were tempered martensite.

关键词

Keywords

references

浏览量

137

下载量

CSCD

文章被引用时，请邮件提醒。

提交

工具集

关联资源

A100钢干式高速铣削表面粗糙度控制研究

高加速电压对电子束焊接TA15钛合金接头热行为及组织性能的影响

AF1410 钢电子束焊接接头组织及性能研究

TB18 钛合金电子束焊接接头微观组织及力学性能研究

刷式密封结构GH4169+Haynes214电子束焊接组织及密封性能研究