基于非对称变曲率研磨的超硬陶瓷球体超精密制造技术

PASICHNYI Oleg; 赵一丞; 郭旭; 马文启; 江春锦; 胡王杰; 张俊杰

doi:10.16080/j.issn1671-833x.25010140

您当前的位置：

首页 >

文章列表页 >

基于非对称变曲率研磨的超硬陶瓷球体超精密制造技术

专稿 | 更新时间：2026-06-16

- 基于非对称变曲率研磨的超硬陶瓷球体超精密制造技术
- 航空制造技术 2026年69卷第10期页码：14-23
- 作者机构：
  
  哈尔滨工业大学精密工程研究所，哈尔滨 150001
- 作者简介：
  
  张俊杰，教授，博士，研究方向为超精密加工工艺与技术、多轴联动激光加工技术。
- 基金信息：
- DOI：10.16080/j.issn1671-833x.25010140
  中图分类号： V26
- 收稿：2025-09-25，
  
  修回：2025-11-05，
  
  录用：2025-11-26，
  
  纸质出版：2026-05-15
- 稿件说明：
移动端阅览
引文格式：PASICHNYI Oleg，赵一丞，郭旭，等.基于非对称变曲率研磨的超硬陶瓷球体超精密制造技术[J].航空制造技术，2026, 69（10）：25010140.

PASICHNYI Oleg, ZHAO Yicheng, GUO Xu, et al. Ultra-precision manufacturing technology of superhard ceramic balls based on asymmetric variable-curvature grinding[J]. Aeronautical Manufacturing Technology, 2026, 69(10): 25010140.
引文格式：PASICHNYI Oleg，赵一丞，郭旭，等.基于非对称变曲率研磨的超硬陶瓷球体超精密制造技术[J].航空制造技术，2026, 69（10）：25010140. DOI： 10.16080/j.issn1671-833x.25010140.

PASICHNYI Oleg, ZHAO Yicheng, GUO Xu, et al. Ultra-precision manufacturing technology of superhard ceramic balls based on asymmetric variable-curvature grinding[J]. Aeronautical Manufacturing Technology, 2026, 69(10): 25010140. DOI： 10.16080/j.issn1671-833x.25010140.

摘要

大尺寸超硬陶瓷球体因优异的力学性能与耐磨特性，广泛应用于高端精密轴承和关键传动系统。然而，陶瓷球体的硬脆特性及尺寸效应使得在其研磨加工过程中难以兼顾球体形状精度与表面质量。针对这一问题，提出一种基于非对称变曲率研磨的超硬陶瓷球体高效超精密制造技术，通过改善研磨迹线覆盖均匀度和时效来提高大尺寸陶瓷球的加工精度和效率。首先，基于多点接触运动学原理，建立球体研磨迹线覆盖的数学模型，系统地分析V形导向槽几何构型对陶瓷球体材料去除均匀性的影响规律。随后，设计并制作了3种典型导向槽研磨盘，通过对比试验研究它们对不同尺寸球体的研磨性能。试验结果表明，当球体直径减小至41.21 mm以下时，传统旋转对称导向槽的研磨性能显著下降，而非对称变曲率导向槽在整个尺寸范围内均保持较高的研磨覆盖均匀度与稳定的材料去除率，从而实现了球形误差与表面粗糙度的更优控制。最后，采用非对称变曲率研磨技术和优化工艺参数制备了直径41.20 mm的氮化硅陶瓷球，其球形误差优于130 nm，表面粗糙度低于6 nm。所提非对称变曲率研磨技术为大尺寸高精度陶瓷球的高效超精密制造提供了理论依据与技术方法。

Abstract

Large-size superhard ceramic balls are increasingly employed in high-end precision bearings and critical transmission systems

owing to their superior mechanical properties and wear resistance. However

their high hardness

brittleness

and size effect make it difficult to simultaneously achieve high form accuracy and excellent surface quality during grinding. To address this challenge

this study proposes an efficient ultra-precision manufacturing technology for ceramic balls based on asymmetric variable-curvature grinding

which is designed to improve the uniformity of grinding trajectory coverage and also enhance machining efficiency. A mathematical model of grinding trajectory coverage is first established based on multi-point contact kinematics

and the influence of the V-groove geometry on the material removal uniformity of ceramic balls is systematically analyzed. Three typical groove-structured grinding plates are then designed and fabricated

with which comparative experiments are conducted to investigate their grinding performance under varying ball diameters. The results indicate that when the ball diameter decreases below 41.21 mm

the grinding performance of the conventional rotationally symmetric groove declines significantly

whereas the asymmetric variable-curvature grooves maintain high coverage uniformity and stable material removal

thereby ensuring superior control of sphericity error and surface roughness. Finally

a sphericity error better than 130 nm and a surface roughness below 6 nm are achieved for silicon nitride ceramic balls with a diameter of 41.20 mm

by the proposed asymmetric variable-curvature grinding technology together with optimized process parameters

which provides theoretical and technical support for the efficient ultra-precision manufacturing of high-precision large-size ceramic balls.

关键词

Keywords

references

王东峰，赵翀，李超强，等.滚动轴承设计技术研究现状及发展趋势[J].轴承，2023(5): 1-5, 12.

WANG Dongfeng, ZHAO Chong, LI Chaoqiang, et al. Research status and development trends of design technology for rolling bearings[J]. Bearing, 2023(5): 1-5, 12.

YAN C, ZHAO M, LIN J, et al. Fault signature enhancement and skidding evaluation of rolling bearing based on estimating the phase of the impulse envelope signal[J]. Journal of Sound and Vibration, 2020, 485: 115529.

LI X Q, JIANG H K, NIU M G, et al. An enhanced selective ensemble deep learning method for rolling bearing fault diagnosis with beetle antennae search algorithm[J]. Mechanical Systems and Signal Processing, 2020, 142:106752.

HWANG Y K, LEE C M. Development of a newly structured variable preload control device for a spindle rolling bearing by using an electromagnet[J]. International Journal of Machine Tools and Manufacture, 2010, 50(3): 253-259.

WANG Q B, XU K, KONG X G, et al. A linear mapping method for predicting accurately the RUL of rolling bearing[J]. Measmrement, 2021, 176:109127.

NATHAN KATZ R, HANNOOSH J G. Ceramics for high performance rolling element bearings: A review and assessment[J]. International Journal of High Technology Ceramics, 1985, 1(1):69-79.

ZHANG W X, REN C Z, ZHENG F, et al. Shaping of green ceramic balls and precision lapping of ceramic balls for ceramic ball bearings[J]. Key Engineering Materials, 2004, 259-260: 471-475.

HANNA S B, AWAAD M, AJIBA N A. Oxidation resistance, compressive strength and thermal shock resistance of SiC ceramics prepared by two processing routes[J]. Silicon, 2020, 12(4):761-772.

WANG L, SNIDLE R W, GU L. Rolling contact silicon nitride bearing technology:A review of recent research[J]. Wear, 2000, 246(1-2): 159-173.

朱鹏娟，刘晓玲，周亚林，等.混合陶瓷球轴承的热混合润滑性能分析[J].机械工程学报，2024, 60(15): 205-215.

ZHU Pengjuan, LIU Xiaoling, ZHOU Yalin, et al. Analysis of thermal mixed lubrication performance in hybrid ceramic ball bearings[J]. Journal of Mechanical Engineering, 2024, 60(15):205-215.

高艺枫，李颂华，魏超，等.氮化硅陶瓷球轴承的沟道波纹度超精工艺调控[J].现代制造工程，2024(12): 102-107.

GAO Yifeng, LI Songhua, WEI Chao, et al. Superfinishing process control of raceway waviness in silicon nitride ceramic ball bearings[J]. Modern Manufacturing Engineering, 2024(12):102-107.

杨铁滨，王黎钦，古乐，等.氮化硅陶瓷球精加工表面缺陷的研究[J].润滑与密封，2006, 31(7): 45-47, 70.

YANG Tiebin, WANG Liqin, GU Le, et al. Surface defects analysis of Si 3 N 4 bearing balls in lapping process[J ] . Lubrication Engineering, 2006, 31(7): 45-47, 70.

朱亮，李言.材料特性对风电轴承耐久性的影响[J].西安理工大学学报，2009, 25(4): 460-465.

ZHU Liang, LI Yan. Influence of wind power generator bearing's material properties on the durability[J]. Journal of Xi'an University of Technology, 2009, 25(4): 460-465.

MURTHY V S R, KOBAYASHI H, TSUREKAWA S, et al. Influence of humidity and doping elements on the friction and wear of SiC in unlubricated sliding[J]. Tribology International, 2004, 37(5): 353-364.

KANG J, HADFIELD M. A novel eccentric lapping machine for finishing advanced ceramic balls[J]. Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture, 2001, 215(6): 781-795.

ZHOU F F, YUAN J L, LYU B H, et al. Kinematics and trajectory in processing precision balls with eccentric plate and variable radius V-groove[J]. The International Journal of Advanced Manufacturing Technology, 2016, 84(9): 2167-2178.

ZHAO P, GUO W G, FENG M, et al. A novel lapping method for high precision balls based on variable-radius V-groove[J]. Journal of Micro and Nano-Manufacturing, 2013, 1(4): 041007.

马文启.基于圆弧拼接变曲率V形槽的氮化硅球体高效研磨方法研究[D].哈尔滨：哈尔滨工业大学，2022.

MA Wenqi. Study on efficient grinding method of silicon nitride sphere based on arc splicing V-groove with variable curvature[D]. Harbin: Harbin Institute of Technology, 2022.

浏览量

下载量

CSCD

文章被引用时，请邮件提醒。

提交

工具集

关联资源

基于磨料射流抛光的新型抛光液制备及抛光性能研究

A100钢干式高速铣削表面粗糙度控制研究

基于微量润滑的Al–60% Si合金铣削性能试验研究

TC4磨削表面晶粒取向演变及微观形貌试验研究

K417G铸造高温合金喷丸强化表面完整性试验研究